|
|
||||
 |
 |
 |
 |
 |
 |
| Ford Rear Super Duty F-250/350 (Fits99-07) | |
| Available bare steel Only | |
| Available in 2 styles Basic and Deluxe (deluxe shown) |
 |
| Deluxe - includes Auxiliary Lights and Backup
Sensor holes (lights included) Basic (not shown) - Same construction, but w/o lights and sensor holes |
|
| Mounting: | |
| The bumper mount plates have four holes per side.
To improve the strength of the mounting system, we not only use the two
stock bumper bolts per side, but extra angle forms were added to also utilize
the trailer hitch bolts along the bottom of each frame rail. Rest assured,
the bumper is securely attached to the frame! Spacer plates are included
to correctly position the factory trailer hitch with our brackets. Along
with the auxiliary lights, the Deluxe model allows you to retain your factory
backup sensors (where applicable). Options include a pair of welded-on shackle
tabs and a 2" receiver between the draw-bars |
 |
| Material: | |
| 1/4" steel outer wings; 1/2" steel center-section;
3/8" steel frame-plates; 1/4" x 3" x 3" steel frame-rail
angle-forms. Optional Shackle Tabs are cut from 1" thick steel with
a 7/8" hole drilled for use with a screw-pin type clevis or shackle |
|
 |
 |
|
 |
 |
|
Description Price
Basic Rear bumper $649 Deluxe Rear bumper $795 Optional Shackle Tabs add $65 Optional 2" Receiver tube add $75 PRICES AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE |
||
| Ford ’99 to '07 F-250-F350 Super Duty/Excursion Front Bumper | ||
| Always specify model and year when ordering. Available in bare steel only. |
 |
|
| Features: | ||
| Viking Steel Fab full-size front bumpers for Ford Super Duty trucks are available in three styles to fit the '99 to '07 models. Basic (not shown), Pre-Runner and Full Brush-Guard are available in both winch and non-winch applications. They now all include the recessed rectangular light holes for mounting aftermarket auxiliary lighting, and are fully vented for improved airflow through the radiator and the many other cooling devices found on modern trucks. Especially diesel equipped rigs. This assures you that your truck will have at least as good cooling as it was designed at the factory to have. If you want to retain your factory fog lights, many customers have found ample room to mount them down low in those same vents without concern for airflow |
 |
|
| Mounting: | ||
| Four 1/2" grade 8 carriage bolts with flatwashers, lockwashers and lock-nuts are used on each side. In addition, our special frame mounting brackets utilize the factory tow hook mounting locations for a super strong, and easy installation. This also allows the factory tow hooks to be retained. | ||
| Material: 1/4" steel on outer forms and some frame mount plates, 3/8" steel on main frame mount plates and grill guard plates. Tubing is .120 wall and varies in diameter according to application |
||
|
Description
|
Finish
|
|
|
Basic Front Bumper (non-winch)
|
$1397 bare
|
 |
|
Front bumper w/Pre-Runner bars
|
$1629 bare
|
|
|
Front Bumper w/ Grill Guard and Outer Headlight Tubes
|
$1750 bare
|
|
|
Options
|
||
|
Winch Ready - fits most models from 10,000 - 16,500
lb ratings - Add $76
|
||
|
Clevis Tabs - 1" Thick for use with screw-pin type
Clevises or Shackles (clevis not included) Add $65
|
 |
|
|
2" Receiver Tube - Frenched in to the lower angle
for use as an accessory mount or for easier trailer maneuvering. Add $110
|
||
|
PRICES AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT
NOTICE
|
||
